A device receives an IP address for a set period before the assignment expires. Devices usually renew it early, so a renewal shouldn’t interrupt your connection.
If phones, computers, or a work VPN disconnect at regular intervals, distinguish the router’s home-network setting from the separate lease assigned by your ISP. They are different settings, so changing the wrong one won’t fix the problem.
This post may contain affiliate links. If you make a purchase through these links, I may earn a small commission at no extra cost to you.
Key Takeaways
- On a NETGEAR home network, the DHCP server assigns local addresses, while your ISP or upstream gateway assigns the WAN address.
- A DHCP reservation keeps a device’s local address consistent, but doesn’t stop it from renewing its lease.
- Repeated outages during lease renewal need troubleshooting. A longer lease may reduce their frequency without fixing the cause.
How NETGEAR DHCP Lease Time Works
DHCP stands for Dynamic Host Configuration Protocol. It automatically supplies an IP address and other network settings when a device connects.

What DHCP Mode Means
A phone or computer using DHCP requests network settings instead of requiring you to enter them manually. On a home network, the DHCP server usually answers that request.
The lease gives a device permission to use its assigned IP address for a set period. It doesn’t measure Wi-Fi strength, internet speed, or how long the device can stay connected.
A manually configured static IP works differently. A lease renewal doesn’t change that manually entered address.
When Devices Renew
Under the DHCP protocol’s renewal rules, clients normally begin renewing halfway through the lease unless the server supplies different timers.
With a one-hour lease, renewal usually begins around 30 minutes. If that attempt fails, the client keeps trying while its existing lease remains valid.
A successful renewal extends permission to use the address. It doesn’t require a new address or a Wi-Fi reconnection.
A DHCP log entry alone doesn’t prove an outage. Match its timestamp with an actual connection failure before changing settings.
Local Leases and WAN Leases Are Different
DHCP can work in two directions. This distinction matters when every device loses internet access together.
Your Home Devices Use LAN Leases
In Router Mode, the DHCP server usually assigns private local addresses to phones, printers, computers, and smart-home equipment.
In Access Point Mode, an upstream gateway normally handles those assignments. Changing settings on the access point won’t change its lease policy.
Use our NETGEAR DHCP reservation guide when a printer, camera, or home server needs a consistent local address.
Your Router Receives a WAN Lease
When internet service uses DHCP, the NETGEAR router acts as a client on its WAN port. The ISP determines that lease.
Changing your home DHCP pool won’t extend a WAN lease controlled by your ISP. A LAN reservation also won’t make your public address static.
When every wired and wireless device loses internet together, check WAN status and upstream equipment. When only one device fails, investigate its local connection first.
Choosing a Practical Lease Duration
There isn’t one universal lease time on NETGEAR. Defaults and available controls depend on the model, firmware, and device handling address assignments.
A commonly cited example describes a subnet with “255 possible addresses,” a 253-address DHCP pool, and a one-hour default. A typical IPv4 /24 actually has 256 total addresses and 254 usable host addresses. Assigning one usable address to the router leaves 253 for clients, assuming no other exclusions.
Subnet size doesn’t automatically determine the lease duration.
These durations help put the settings in perspective.
| Lease duration | Seconds | Practical use |
|---|---|---|
| 20 minutes | 1,200 | Public networks with frequent visitor turnover |
| 1 hour, or 60 minutes | 3,600 | A shorter lease requiring more frequent renewals |
| 1 day | 86,400 | A reasonable starting point for a stable home network |
| 30 days | 2,592,000 | Long-lived assignments where address availability permits |
For a home with roughly 30 to 40 regularly connected devices, a day is a practical starting point if the setting is adjustable. A 30-day lease can work, but rarely offers a clear household benefit.
A coffee shop may use 20 minutes because some visitors stay only two or three minutes. Short leases help reclaim addresses after visitors leave. They don’t disconnect active customers who renew successfully.
Can You Change the DHCP Setting on NETGEAR?
Some products expose a lease duration field. Others provide DHCP pool and reservation controls without an adjustable timer.
Find the Available LAN Settings
On many models, open the browser interface and go to ADVANCED > Setup > LAN Setup. Available menus vary by firmware.
Look for an explicit lease-duration field. If none appears, don’t assume the starting and ending values control it. Those fields define the address pool.
NETGEAR’s SRR60 firmware release notes document lease-duration configuration on that business product. That doesn’t establish support across Nighthawk, Orbi, or every home model.
Change Only the Relevant Setting
Before making changes, save your NETGEAR router configuration. Record the current pool, device address, and reservations.
If a lease field exists, pay attention to its units. Entering 1,440 into a seconds field produces 24 minutes, not one day.
Leave WAN settings alone when adjusting local leases. Don’t select a static internet address to avoid DHCP unless your service includes the required static settings.
Managed-Switch Instructions Don’t Apply to Home Routers
Some NETGEAR DHCP search results describe managed switches rather than household routers. Their menus and commands aren’t interchangeable.
One documented switch procedure enables Admin Mode, selects Apply, then creates a pool with type Manual. It uses Hardware Type ethernet, a Client ID consisting of 01 followed by the hardware address, and Days set to 1.
The corresponding CLI procedures use commands including ip routing, ip dhcp pool, network statements such as 10.200.1.0 255.255.255.0, ip dhcp excluded-address, and service dhcp.
Listed firmware families include M5300 10.0.0.x, M4100 10.0.1.x, M7100 10.0.1.x, and XSM7224S 9.0.1.x.
These instructions describe business-switch DHCP features. They aren’t a workaround for a missing lease-time field on a home NETGEAR router. Applying unrelated network commands or pool settings can create additional connection problems.
Troubleshooting Disconnects During Lease Renewal
Normal renewal shouldn’t cycle LAN ports or interrupt a VPN. Either symptom points to a problem worth isolating.

Follow this sequence before changing lease lengths.
- Record outage times and compare them with DHCP and WAN entries. Our NETGEAR router log guide explains common messages.
- Test a computer over Ethernet. If the wired internet connection works while Wi-Fi fails, investigate wireless coverage or the affected client.
- Check WAN status during the outage. An address of
0.0.0.0means the device hasn’t obtained an upstream address. Check the cable connected to the WAN port, then try a known-good replacement. - Save the configuration before firmware changes. If restarting equipment, let the modem or gateway reconnect first, then power up the device.
NETGEAR’s community includes an R7400 WAN-renewal disconnect report. Such reports document symptoms, not a universal fix.
Another forum user reported VPN interruptions when an ISP lease returned to one hour after being extended beyond a day. That pattern supports investigating WAN renewal, but doesn’t establish the cause.
An XR500 owner reported multiple daily “new lease” entries with fewer than 15 devices, despite reservations and disabled QoS. Changing the pool from addresses ending in 2 through 254 to 100 through 200 reportedly prevented internet access. Don’t copy that change as a fix.
If lights on the LAN ports actually cycle, record that separately. A physical link reset differs from ordinary DHCP activity.
Frequently Asked Questions
Does Release and Renew Change My IP Address?
Not necessarily. It requests another lease, and the DHCP server may assign the same address. For a provider-facing connection, the upstream server decides which address your equipment receives.
On supported NETGEAR interfaces, WAN connection status includes Release and Renew controls. Using Release deliberately interrupts that connection.
On Windows, ipconfig /release followed by ipconfig /renew renews the computer’s local lease. On macOS, use the connection’s TCP/IP settings and select Renew DHCP Lease.
MAC address spoofing may produce a different provider-assigned address, but it isn’t guaranteed and can cause authorization problems.
Should I Use a DHCP Reservation?
Use one when a printer, camera, NAS, or forwarding rule depends on a consistent local address. NETGEAR’s address reservation instructions describe adding entries under LAN Setup.
The device still uses DHCP and renews its lease. A reservation won’t prevent an upstream internet outage or fix weak Wi-Fi.
Do I Need a New Router?
A renewal-related drop alone doesn’t prove the equipment needs replacement. Check the internet connection, WAN cabling, provider service, and firmware first.
If replacement becomes necessary, Better WiFi Shop offers equipment comparisons. Buying mesh equipment primarily for coverage won’t resolve a provider-controlled lease problem.
Focus on the Connection That Fails
The useful distinction is whether the local connection or internet connection is failing. It tells you which device controls the lease and which settings can affect it.
Keep working lease settings unless you have a clear reason to change them. For a recurring disconnect, match the timing, compare Ethernet with Wi-Fi, and identify whether the router’s local connection or WAN connection is failing before replacing equipment.
