Change Your NETGEAR Router’s LAN IP Without Losing Access

A brief disconnect is normal when you change your router’s LAN IP address. Planning the new address and matching DHCP settings helps prevent losing access.

Know your new login address before clicking Apply. Your computer may also need a fresh IP address before it can reach the router again.

Start by separating the router’s local address from the other IP settings on your network.

This post may contain affiliate links. If you make a purchase through these links, I may earn a small commission at no extra cost to you.

Key Takeaways

  • Changing the LAN IP causes a temporary disconnect. Have the new address written down before saving.
  • The router address, DHCP pool, and connected devices must use compatible subnet settings.
  • Renew your computer’s address after the change. Try local recovery steps before considering a factory reset.

Understand Which IP Address You’re Changing

The LAN Address Opens Your Router Settings

The LAN IP address is your router’s local address on your home network. Your devices also use it as the default gateway to reach other networks.

Many NETGEAR routers use 192.168.1.1 by default with a subnet mask of 255.255.255.0. Some models use 192.168.0.1, while existing configurations may use another address.

Changing this address changes where you open the administrator dashboard. It doesn’t change your Wi-Fi name or password.

WAN Addresses and Device Reservations Are Different

Your router’s WAN address belongs to its internet-facing connection. Setting a static WAN IP under Internet Setup is a separate task.

A DHCP reservation assigns a consistent local address to a printer, camera, or computer. It doesn’t change the router’s own LAN address.

If your goal is keeping a printer at one address, use a reservation instead of changing the whole network.

Prepare Before Changing the LAN IP

A black Wi-Fi router on a wooden shelf with glowing blue network lines around it.

Connect Locally and Save Your Settings

Use a computer connected to a router LAN port by Ethernet when possible. Your main NETGEAR Wi-Fi network also works.

Avoid guest Wi-Fi, which may block access to local administration. Temporarily disconnect any VPN. On a phone, turn off mobile data so it doesn’t switch networks during the restart.

Save a configuration backup before editing. Our NETGEAR backup and restore guide covers protecting your existing settings.

Record the current LAN address, subnet mask, DHCP range, reservations, and port-forwarding destinations.

Use the Administrator Login

For router login, enter routerlogin.net or routerlogin.com in your browser’s address bar, not a search box. You can prefix either address with http://.

You can also enter the current gateway IP, such as 192.168.1.1. NETGEAR’s router login instructions describe browser access.

On older, untouched models, the default username is admin and the default password is password. Both are case-sensitive.

Use your current administrator password if you changed it during setup. Your Wi-Fi password and NETGEAR account password are separate credentials.

Use a browser for these advanced settings, since the Nighthawk app may show different options across models.

Choose a New Address and Matching DHCP Range

For a straightforward change to 192.168.10.1, keep the subnet mask at 255.255.255.0. This creates a local network with addresses beginning with 192.168.10.

Choose a subnet that doesn’t overlap your upstream ISP gateway or a network used by your VPN. Two connected routers using the same subnet can cause routing problems.

Here’s an example address plan with the DHCP range moved to the new subnet:

SettingBeforeAfter
Router LAN IP192.168.1.1192.168.10.1
Subnet mask255.255.255.0255.255.255.0
DHCP starting address192.168.1.100192.168.10.100
DHCP ending address192.168.1.199192.168.10.199
Reserved printer address192.168.1.120192.168.10.120

Changing the subnet affects device addresses too. The router, DHCP pool, and manually assigned addresses must use compatible addresses on the new subnet.

With this mask, don’t assign 192.168.10.0 or 192.168.10.255 to devices. Keep the router’s .1 address out of the DHCP pool.

Manually configured device addresses should be outside the automatic pool or excluded from automatic assignment. Each address must belong to only one device.

Changing only the router address while leaving clients on the old subnet can make a working router appear unreachable.

Change Your NETGEAR Router IP in LAN Setup

Use the browser dashboard for this change. The Nighthawk app can show connected devices, but it may not expose every advanced LAN setting. If you usually use the Nighthawk app, open the router dashboard in a browser to change the LAN address.

NETGEAR’s LAN TCP/IP instructions describe the standard menu path.

  1. Sign in with the router’s current LAN address and administrator credentials.
  2. Open ADVANCED > Setup > LAN Setup. Some models or firmware versions use BASIC > Setup > LAN Setup instead.
  3. In IP Address, enter your planned address, such as 192.168.10.1.
  4. Review IP Subnet Mask. Keep 255.255.255.0 for this example. A different mask changes which addresses belong to the same network.
  5. Check the DHCP server’s starting and ending addresses. Update them to match the new subnet if they don’t change automatically.
  6. Leave RIP settings unchanged unless your network requires dynamic routing. RIP Direction options include Both, Out Only, and In Only. RIP Version options include Disabled, RIP-1, and RIP-2, sometimes listed as RIP-2B or RIP-2M.
  7. Click Apply or Save, depending on the interface. The connection will drop while the router applies the change and restarts.

RIP controls routing-information exchange between routers. Most home networks don’t need changes to these settings.

Wait for the router to finish restarting before reconnecting. Don’t unplug it if the browser stops responding. The old dashboard address will no longer work, which is expected.

Reconnect After the Router Restarts

A router connected to various devices via glowing blue lines on wooden shelves.

Request a Fresh DHCP Address

Your computer may still hold an address beginning with 192.168.1. It needs an address in the new subnet to communicate normally.

On Windows, open Command Prompt to release and renew IP settings. Run ipconfig /release, then run ipconfig /renew. These commands release the existing DHCP lease and request another.

Carnegie Mellon University’s release and renew instructions explain this DHCP process.

On a Mac, open System Settings, then your network connection’s Details. Under TCP/IP, select Renew DHCP Lease.

Disconnecting and reconnecting Wi-Fi or Ethernet also usually requests a new lease. DHCP renewal won’t change a manually configured static IP address.

Close the Browser and Use the New Address

Close your browser, relaunch it, and enter 192.168.10.1 directly in the address bar. Sign in with the same administrator credentials.

On Windows, ipconfig should show an IPv4 address in the new subnet and 192.168.10.1 as Default Gateway. On a Mac, network details show the gateway under Router.

Open a website after the dashboard loads. This confirms local access and a working internet connection.

Devices may reconnect automatically, but don’t assume every printer, camera, or smart-home hub has updated.

Update Devices That Depend on Fixed Addresses

Repair Reservations and Manual Static IPs

Review saved reservations after changing the subnet. Firmware behavior varies, so don’t assume every old entry was converted.

NETGEAR’s address reservation instructions explain how to add an entry.

Assign each reserved device an unused address in the new subnet, then reconnect or restart it. Our NETGEAR DHCP reservation guide covers printers, cameras, and smart devices.

For manually configured devices, update the IP address, subnet mask, gateway, and any DNS entry that references the old router address.

Update Rules and Saved Connections

Port-forwarding rules must point to each device’s new local address. Our NETGEAR port-forwarding guide explains how to keep that destination consistent.

Also update printer ports, camera recorder settings, NAS shortcuts, and applications that connect by IP address.

Reconnect a test device and confirm its normal task works. A successful dashboard login doesn’t prove that printing, local storage, or camera viewing still works.

Recover Access If the Login Page Won’t Open

Rule Out the Wrong Network or Stale Browser

Make sure you’re connected to the main NETGEAR network. A phone on cellular data or a computer using another gateway won’t reach the intended dashboard.

Try routerlogin.net or routerlogin.com first. If neither works, type the new numerical address directly to bypass a hostname-resolution problem.

Clear the browser’s cache and cookies if it displays old content or a stuck login page. Try another browser and a direct Ethernet connection.

NETGEAR’s access troubleshooting guide covers these local connection problems. Our NETGEAR router login recovery guide also explains how to find your current gateway.

Try Local Recovery Before a Factory Reset

If DHCP renewal fails, check for a DHCP or subnet mismatch first. Then temporarily assign your computer an unused static IP address in the planned subnet. For this example, 192.168.10.10 with mask 255.255.255.0 can reach 192.168.10.1.

Repair DHCP in the dashboard, then return the computer to automatic addressing.

If the change wasn’t saved, the router may still answer at its old address. Try that address with compatible computer settings.

For a forgotten password, try saved credentials or previously enabled password recovery first. A factory reset erases custom settings and restores factory defaults, including applicable default credentials. Newer models may require creating a password during setup again.

Common Questions About Changing the LAN IP

Will Changing the LAN IP Change My Public IP?

Changing the LAN address doesn’t change your public internet address. Your ISP-facing connection uses separate WAN settings. It also won’t fix weak Wi-Fi coverage or increase your internet plan’s speed.

Do I Always Need to Release and Renew?

Some devices reconnect and obtain a new address automatically. Renew manually when your computer keeps the old subnet or gateway. If the computer uses a static IP, edit its settings instead.

What Subnet Mask Should I Use?

Use 255.255.255.0 for the 192.168.10.1 example. Changing the third number doesn’t require changing this mask. Use another mask only when your network plan requires a different subnet size.

Keep a Clear Path Back to Your Router

A safe LAN address change depends on a matching address plan. Write down the new router address, align DHCP, and renew your computer’s connection afterward.

Keep the backup until reservations, printers, and forwarding rules work again. A temporary disconnect is expected; the new address and compatible device settings give you a clear way back in.